Query Results Report

Native Flags for IMPROVE RHR Metrics III, Annual Group Means

Here are your query results:

ProtocolID	Flag	StatusFlag	Description	FlagType	SourceColumn
1007		V4	Unknown	Temporary	FLAG_%
1007	0	M1	Data points with NULL values in Debbie Miller's RHR data that have a '0' value in the flag_a, flag_b, flag_c, or flag_d field.	Quality Assurance	FLAG_%
1007	AA	M2	ORGANIC ARTIFACT CORRECTED	Quality Assurance	FLAG_%
1007	AP	V5	Possible Organic Artifact	Quality Assurance	FLAG_%
1007	BI	M2	Incorrect installation of sample cartridge during weekly change	Quality Assurance	FLAG_%
1007	CG	V6	Flowrate less than 18 liters per minute for more than 6 hours	Quality Assurance	FLAG_%
1007	CL	M3	Flowrate less than 15 liters per minute for more than 6 hours	Quality Assurance	FLAG_%
1007	DA	M1	Did not analyze	Quality Assurance	FLAG_%
1007	DE	V2	Derived value	Quality Assurance	FLAG_%
1007	DF	V4	Unknown	Unknown	FLAG_%
1007	EE	V4	Unknown flag	Temporary	FLAG_%
1007	EP	M1	Equipment Problem	Quality Assurance	FLAG_%
1007	LC	V0	Unknown	Unknown	FLAG_%
1007	LD	V0	Below detection limit - at one point this flag was mapped to 'NM'	Quality Assurance	FLAG_%
1007	LF	V6	The flow is greater than 10% higher or lower than the nominal flow rate. This effects the cut point of the particle but the concentrations are correct.	Quality Assurance	FLAG_%
1007	MM	V4	Unknown	Unknown	FLAG_%
1007	NA	M1	Not Applicable. This is used for missing modules with non-protocol samplers with less than four modules.	Quality Assurance	FLAG_%
1007	NM	V0	NORMAL	Quality Assurance	FLAG_%
1007	NR	V0	Samples that have OP=0 that may actually have a negative OP.	Quality Assurance	FLAG_%
1007	NS	M1	Operator did not install the samples or installed them too late to acquire a valid time. All filters involved.	Quality Assurance	FLAG_%
1007	OL	M1	Off Line. In some cases, this is used when the sampler is inoperable due to hurricane or fire. For year 2000, this is used for the period after the Version 1 sampler is removed and before the Version 2 samples begins operation.	Quality Assurance	FLAG_%
1007	PC	V5	Possible contamination	Quality Assurance	Status
1007	PO	M1	Power Outage. All filters involved.	Quality Assurance	FLAG_%
1007	QA	I1	QA problem suspected, value held back for further investigation	Quality Assurance	FLAG_%
1007	QC	V4	Valid value despite failing to meet some QC or statistical criteria.	Quality Assurance	FLAG_%
1007	QD	V4	Questionable data	Quality Assurance	FLAG_%
1007	QV	V4	Data quality check (internal use only)	Quality Assurance	FLAG_%
1007	RF	V6	The flow is greater than 20% higher or lower than the nominal flow rate. This affects the cut point of the particle but the concentrations are correct.	Quality Assurance	FLAG_%
1007	SA	V6	Used to indicate some sort of 'Sampling Anomaly', though the exact definition has yet to be satisfactorily defined.	Quality Assurance	FLAG_%
1007	SD	V6	Short Duration Sample; The sample is too short for use in calculating RHR metrics, but it is still a meaningful result that is useful in other contexts.	Quality Assurance	FLAG_%
1007	SE	V0	Unknown	Unknown	FLAG_%
1007	SO	V4	Sent Out	Temporary	FLAG_%
1007	SP	V0	An artifact filter was swapped with a sample filter.	Quality Assurance	FLAG_%
1007	SW	V0	Suspected filter swap.	Quality Assurance	FLAG_%
1007	TO	V6	Timing Outside normal bounds	Quality Assurance	Flag_%
1007	TU	V6	Non-standard sampling conditions	Quality Assurance	FLAG_%
1007	UN	M2	The concentrations failed the data validation for unknown reasons.	Quality Assurance	FLAG_%
1007	XX	M2	The filter is damaged.	Quality Assurance	FLAG_%